WIRING SYSTEM(18 GAUGE)

MAIN HARNESS(18 GAUGE)

NAME CODE DIMENSION APPLICATION
Harness1 AWH1 1500 mm Part of the main harness line.Enables 1 direct light connection, or light splitter to add 2 or more lights.
Harness4 AWH4 6110 mm Part of the main harness line.Enables 4 direct light connections, or light splitter to ad 4 or more lights.
Harness Extend 5 AWHE5 5000 mm Part of the main harness line.Enables harness to be extended 5000mm where light connection points are not required.
Harness Extend 10 AWHE10 10000 mm Part of the main harness line.Enables harness to be extended 10000mm where light connection points are not required.
Harness Splitter 2 AWHS2 300 mm Part of the main harness.Enables harness to be split to 2 directions.
Harness Female Connector AWHF 300 mm Connector with IP68 capability used to connect with Harness wire to make customised lengths of harness.
Harness Male connector AWHM 300 mm Connector with IP68 capability used to connect with Harness wire to make customised lengths of harness.

WIRING SYSTEM

LIGHT WIRING(20 GAUGE)

LIGHT EXTENSION & LIGHT SPLITTERS(20 GAUGE)

NAME CODE DIMENSION APPLICATION
Light Extend 3.6 AWLE3.6 3660 mm Part enables light positioning 3600mm beyond the 900mm light lead which is supplied with each LTLT LED light.Eg used to extend up into trees or fences.
Light Splitter 2 AWLS2 300 mm length Part connects to Harness light connection point when 2 lights are required in the same area.Creates 2 light ports from the 1 Harness Light connection point.
Light Female Connector AWLF 300 mm Connector with IP68 capability is a female connection plug to fit an LTLT light.This component is recommended when hardwiring and not using the LTLT Harness with built in connection points.
Light Male Connector AWLM 300 mm Connector with IP68 capability is used to make custom length light extensions.

WIRING COMPONENTS. . . DIY

NAME CODE DIMENSION APPLICATION
Harness Wire AWHW18AWG 18 gauge by the metre or 100 m roll 18 gauge extension wire is used to customise harness extensions
Harness Blue Connector AWHWCB 12 mm x 12 mm Connector with IP68 capability used to connect Harness wire when customising or repairing Harness wire

TRANSFORMERS

WEATHER PROOF TRANSFORMER

NAME CODE DIMENSION APPLICATION
1.25 Amp 12V DC Power Supply WP ATF12V1.25DCWP L      128 mm
W      52 mm
D       32 mm
Includes:
500 mm AC lead Harness plug
Part used to drive upto 1 Amp or 1000 mA (see light Spec Sheets for mA).

Can be situated outdoors IP67.
2.92 Amp 12V DC Power Supply WP ATF12V2.92DCWP L      128 mm
W      52 mm
D       32 mm
Includes:
500 mm AC lead Harness plug
PArt used to drive up to 2.3 Amps or 2300 mA(see light Spec Sheets for mA)

Can be situated outdoors IP 67
5 Amp 12V DC Power Supply WP ATF12V5DCWP L      242 mm
W      52 mm
D       32 mm
Includes: 500 mm AC lead Harness plug
Part used to drive up to 4 Amps or 4000 mA (see light Spec Sheets for mA)

Can be situated outdoors IP67
8.3 Amp 12V DC Power Supply WP ATF12V8.3DCWP L      236 mm
W      60 mm
D      355 mm
Includes: 500 mm AC lead Harness plug
Part used to drive up to 7 Amps or 7000 mA (see light Spec Sheets for mA)

Can be situated outdoors IP 67
12.5 Amp 12V DC Power Supply WP ATF12V12.5DCWP L      180 mm
W      70 mm
D       50 mm
Includes: 500 mm AC lead Harness plug
Part used to drive up to 10 Amps or 10000 mA (see light Spec Sheets for mA)

Can be situated outdoors IP 67

TRANSFORMERS(INDOOR)

NAME CODE DIMENSION APPLICATION
2920mA 12V DC Indoor Power Supply IP20 ATF12V2.92DC L      185 mm
W      43 mm
D       30 mm
Includes: 500 mm AC lead Harness plug
Part used to drive up to 2.3 Amps or 2300 mA (see light Spec Sheets for mA)

Indoor use only
5 Amp 12 V DC Indoor Power Supply IP20 ATF12V5D L      254 mm
W      45 mm
D       35 mm
Includes: 500 mm AC lead Harness plug
Part used to drive up to 4 Amps or 4000 mA (see light Spec Sheets for mA)

Indoor use only
8.3 Amp 12V DC Indoor Power Supply IP20 ATF12V8.3DC L      270 mm
W      63 mm
D       40 mm
Includes: 500 mm AC lead Harness plug
Part used to drive up to 6.6 Amps or 6600 mA (see light Spec Sheets for mA)

Indoor use only
12.5 Amp 12V DC indoor Power Supply IP20 ATF12V12.5DC L      270 mm
W      63 mm
D       40 mm
Includes: 500mm AC plug Harness plug
Part used to drive up to 8.8 Amps or 8800 mA (see light Spec Sheets for mA)

Indoor use only

AC TO DC CONVERTER

AC TO DC CONVERTER OUTDOOR

NAME CODE DIMENSION APPLICATION
Converter 12V AC-DC WP ATFC12vAC-DC2WP L      140 mm
W      60 mm
D       30 mm
Includes: Harness plug
Part used to convert existing 12V transformers from AC to DC.To enable the use of an existing transformer previously used for halogens

Can be situated outdoors IP 65

VOLTAGE REDUCER

VOLTAGE REDUCER 24V-12V DC

NAME CODE DIMENSION APPLICATION
24V-12V Reducer WP ATFR24V-12vDC5WP L      140 mm
W      60 mm
D       35 mm
Includes: Harness plug
Part used to reduce incoming voltage greater than 12v up to 24v to 12v

Can be situated outdoors IP 65

REMOTE CONTROLS

REMOTE CONTROLS OUTDOOR

NAME CODE DIMENSION APPLICATION
Remote Receiver 1 CH. IP 65 ACRR1WP L      170 mm
W     120 mm
D       65 mm
Harness plugs
Part used to Receive Remote Control command(on or off) for 1 Channel/Zone

Can be situated outdoors.IP 65
Remote Receiver 4 CH. IP 65 ACRR4WP L      170 mm
W     120 mm
D       65 mm
Harness plugs
Part used to Receive Remote Control command(on or off) for 4 independant Channels/Zones Can be situated outdoors.IP 65
Remote Transmitter 1 CH ACRT1 L       75 mm
W      40 mm
D       25 mm
Part used to Transmit Remote Control command(on or off) for 1 Channel/Zone
Remote Transmitter 4 CH ACRT4 L       60 mm
W      50 mm
D       25 mm
Part used to Transmit Remote Control command(on or off) for 4 independant Channels/Zones

TIMER-SENSOR

TIMER-SENSOR OUTDOOR

NAME CODE DIMENSION APPLICATION
Sunset Timer ACTS5WP L      100 mm
W      60 mm
D       35 mm

Harness plugs
Part used to recognize the sun setting and triggers the light system on.Can be used to turn off in 2,4 or 6 hours.,or dusk to dawn.
Can be situated outdoors. IP 65

SPIKE MOUNT EXTENSIONS

SPIKE EXTENSIONS

NAME CODE DIMENSION APPLICATION
5 mm 500mm spike aluminim AMS5A500 L      500 mm
W     5 mm
Part used when the mounting spike packaged with the garden light is not long enough to achieve desirable height of light off ground.
5 mm 750 mm spike aluminium AMS5A750 L      750 mm
W     5 mm
5 mm 1000mm spike aluminium AMS5A1000 L     1000 mm
W     5 mm
5 mm 500mm spike Copper AMS5C500 L      500 mm
W     5 mm
5 mm 750mm spike Copper AMS5C750 L      750 mm
W     5 mm
5 mm 1000mm spike Copper AMS5C1000 L     1000 mm
W     5 mm

WALL MOUNT BRACKETS

SURFACE WALL LIGHT MOUNTS

NAME CODE DIMENSION APPLICATION
Wall Bracket AWB50 316 Stainless Bracket is mounted to wall and wall light mounted on bracket.All wall lights come with bracket included.Fits light in the following series: LTWW,LTWE and LTWC.
Wall Bracket AWB100 316 Stainless

TREE CLAMPS

NAME CODE DIMENSION APPLICATION
Tree Clamp 40 AMTC40 40 mm diameter Part used to fix Lights in trees.Easy to move the light to desired position without choking the tree.
Tree Clamp 50 AMTC50 50 mm diameter
Tree Clamp 65 AMTC65 65 mm diameter
Tree Clamp 80 AMTC80 80 mm diameter
Tree Clamp 100 AMTC100 100 mm diameter

MOUNTS

BOLLARD MOUNTS

NAME CODE DIMENSION APPLICATION
Bollard Mount 30 AMB30 Part used to fix Bollards in concrete or soil.Fix mount in concrete.Bollard slips over the top and locks in.
Bollard Mount 12 AMB12
Bollard Mount 6 AMB6

TRIFFID MOUNTS

NAME CODE DIMENSION APPLICATION
Triffid Mount 3 AMT3 Part used to fix Triffid Path Lights and Bollards in concrete or soil.Fix mount in concrete.Triffid or Bollard slips over the top and locks in
Triffid Mount 6 AMT6
Triffid Mount 12
Triffid Mount 21 AMT21
Triffid Mount 30 AMT30

POND MOUNTS

NAME CODE DIMENSION APPLICATION
Small Pond Plate AMPP5 L      100 mm
W      50 mm
D       10 mm
Part fits the spikes of an LTLT "Bondi Barrel" to use under water.The pond pole acts as a weight and gives the light stability.3 sizes available
Large Pond Plate AMPPL L      100 mm
W      50-100 mm
D       10 mm
Flat Pond Plate AMPPF L      150 mm
W     150 mm
D       5 mm

GLARE GUARDS

NAME CODE DIMENSION APPLICATION
Glare Guard LT6 ACC6SSF 32 mm diameter
316 Stainless
The Glare Guard is designed to slip over the light to hide the light source and make the light beam narrower.

The Stainless Steel Glare Guard slips over the existing light fitting of the LT,LTP and LTWP series of LTLT lights.
Glare Guard LT12 AGG12SSF 38 mm diameter
316 Stainless
Glare guard LT21 AGG21SSF 50 mm diameter
316 Stainless
Glare Guard LT30 AGG30SSF 63 mm diameter
316 Stainless
Glare Guard LT6 AGG6CF 32 mm diameter
316 Copper
The Glare Guard is designed to slip over the light to hide the light source and make the light beam narrower.

The Solid Copper Glare Guard slips over the existing light fitting of the LT, LTP and LTWP series of lights.
Glare Guard LT12 AGG12CF 38 mm diameter
316 Copper
Glare guard LT21 AGG21CF 50 mm diameter
316 Copper
Glare Guard LT30 AGG30CF 63 mm diameter
316 Copper